The wall dry–lining insulation shall be Kingspan Kooltherm® K Insulated Dry– lining Board comprising a mm plasterboard facing bonded to ____mm. Kingspan Kooltherm K Super high performance rigid thermoset phenolic insulation; Fibre-free, closed cell insulation core; 3-in-1 insulation, dry-lining and . Kooltherm K17 Insulated Dry-lining Board is an insulated plasterboard for traditional dot and daube plaster adhesive fixing. The tapered edge board enables flat.
|Published (Last):||2 November 2014|
|PDF File Size:||6.31 Mb|
|ePub File Size:||18.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Send Us An Enquiry.
Kooltherm K17 Insulated Plasterboard. Apply 2 per board after the adhesive has set, positioned 15 mm in from the board edge and at mid height with a nominal 25 mm embedment into the wall.
Boards are then located against the adhesive dabs and tapped back to align with predetermined guidelines on the floor and ceiling. Nailable plugs are recommended at a rate of 3 No.
Kooltherm K17 | Forman Building Systems
Installation is similar to that of standard plasterboard. Vertical dabs of the gypsum koltherm are progressively applied to the background together with a continuous fillet at skirting and ceiling level.
Timbers must offer a minimum 20 mm support to all four edges of the koolthrrm. K17 Insulated Dry—lining Board has a gypsum plasterboard face. Product Information Contact Us.
Nailable plugs are recommended to complement the plaster dab bond. Ensure accurate trimming to achieve close butting joints and continuity of insulation. Short lengths of metal framing should be fixed horizontally between the vertical pieces at skirting level, at the midpoint of the board and just below the ceiling or soffit level.
Tap the board back firmly using a straightedge, kootlherm that the vertical edge is plumb. Ensure that safe methods of cleaning are used, as recommended by the suppliers of the spilt liquid. If an acceptable adhesive bond cannot be achieved due to the wall surface, consideration should be given to a mechanically fixed option. The ceiling lining should be in position before wall lining commences.
Fixing should employ the same method as is used for the plain wall areas. Refer to fixing manufacturer instructions for more information. The particular system employed will depend on the construction or design of the koolthedm to which Kingspan Kooltherm K17 Insulated Plasterboard is to be fixed.
Do you need help and advice on your project? Bostik adhesive is applied to the wall surface in strips to a predetermined pattern that coincides with the edges of the board, and then a further strip is applied horizontally at the midpoint of the board.
Kingspan Kooltherm K17 Phenolic Insulated Plasterboard
Test – BS —7: Premium koolthrrm rigid phenolic insulation kooltgerm conductivity as low as 0. If correctly applied, K17 Insulated Wall Board has an indefinite life. If you do not click “Accept and close” but continue to use this website: Water Vapour Resistance Modified to include board facings, the boards achieve a resistance far greater than MN.
The frame should be set vertically at a maximum of mm centres to coincide with board joints and midpoint of board. System R-values Click on the specific application types below to view their System R-values. Traditional Plaster Dab Bonding This method is for applications to brick, block or concrete masonry cavity walls. Method of test to determine the classification of the surface spread of flame of products Result – Class 1 rating Kkoltherm – BS —1: As such, the will reflect light as well as heat, including ultraviolet light.
Cutting should be carried out either by using a fine toothed saw, or by koolherm with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side.
Block Wall mm View System R-value. Boards that have been allowed to get wet should not be used. The insulation core is not resistant to some solvent—based adhesive systems, particularly those containing methyl ethyl ketone. The Selwyn Aquatic Centre in Rolleston provides an aquatic experience that can be enjoyed all year round.
The board should be fully restrained using mechanical fixings.